Glues
Pre-mixed Incollarasa
2 treatments in 1 product!
Reduces thickness compared to plasters and speeds up block laying


Consumption
for skim coating: 1 bag per each pallet (approximately)
for skim coating: 1 bag per 4 m2 (1 side, 5 mm thick.)

Workability
4 hours (approximately)

Water retention
calibrated for GASBETON®

Benefits
Easy to spread
Lightweight and insulating
Ideal for EI/REI masonry
M5 and M10 available
Formation of masonry with GASBETON® aerated autoclaved concrete blocks Apply BONDSKIM with a special notched trowel on the horizontal joint and, for blocks without interlocks, also on the vertical joint. Joint thickness: 1 – 3 mm. The masonry must be protected from rain and from frost for at least 24/48 hours. The blocks may require prior wetting if used in a very hot climate.
Skim coating of walls made with GASBETON® aerated autoclaved concrete blocks Spread the first coat of BONDSKIM with a notched trowel (minimum thickness 3 mm). Apply the glass-fibre crack protection mesh (75 – 160 gr/m2). Spread the second coat of BONDSKIM with a smooth trowel, after min. 2h from the first one (max24h). Total thickness of the skim coating 5 mm (1st coat + mesh + 2nd coat). Final grain size <0.6mm. Note: indoors, the skim coat can be applied directly on the GASBETON masonry, while outdoors it is necessary to apply a primer plaster with MULTICEM beforehand.
RANGE:
BONDSKIM M5 – 25 Kg bag
Ready-to-use premixed
code VCOLLARASA
BONDSKIM M10 – 25 Kg bag
Ready-to-use premixed.
code VCRASM10

Mortarglue M10 RS
Glue with high mechanical strength and high resistance to sulphates for the laying of GASBETON® blocks.
Premixed powder mortar for internal and external masonry, with calibrated water retention, hydraulic binder-based with special additives that provide superior sulphate resistance, specific for the thin joint bonding of GASBETON® blocks, to be applied by hand with a notched trowel. Joint thick.: 1-3 mm
Grain size: 0- 0.6 mm – Colour: white
code VCRASM10 MORTARGLUE premixed M10 RS – 25 Kg bag
code VCRASM10MB MORTARGLUE premixed M10 RS half pallet – 25 Kg bag
Plasters

Multicem
Lightweight plaster for the base plastering of GASBETON® masonry.
Premixed powder mortar for base plasters, suitable for indoor and outdoor use, water-retaining, fibre-reinforced, water-repellent, low specific weight, hydrated lime-based, special hydraulic binders and light aggregates, specifically for application on GASBETON® masonry.
Min. thick.: 1 cm internal, 1.5 cm external. Grain size: 0 – 1.3 mm. Colour: grey.
code VINTO – MULTICEM BASE PLASTER – 25 Kg bag
Skim coats

Multiraso for interiors
Skim coat for MULTICEM or BONDSKIM internal finishing.
Premixed powder mortar for indoor skim coating, with improved workability, aerial binder-based, specific for finishing base coats (MULTICEM plaster or BONDSKIM reinforced skim coat) of GASBETON® masonry, to be applied by hand. The ideal primer for subsequent application of breathable paints. Thick. per coat: min. 1 mm, max. 2 mm. Thick. finished skim coating max. 3 mm. Grain size: 0 – 90 µ. Colour: white.
code VRASINT – MULTISKIM SKIM COAT FOR INTERIORS – 25 Kg bag

Multiskim for exteriors
Reinforced skim coat for exterior MULTICEM base plaster
Premixed powder mortar for outdoor skim coating, fibre-reinforced, water-repellent, hydrated lime and hydraulic binder-based, specific for finishing the base layer (MULTICEM plaster) of GASBETON® masonry. The ideal base for subsequent decorating using plaster finish or silicate or siloxane-based paints. Max. thick.: 2 mm per coat, 5 mm finished skim coating Grain size: 0 – 1.3 mm. Colour: light grey.
code VRASEST – MULTISKIM SKIM COAT FOR EXTERIORS – 25 Kg bag

Rasofin
A unique outdoor skim coat that is breathable, lightweight, fibre-reinforced and water-repellent.
Premixed powder mortar for outdoor skim coating, breathable, lightweight, fibre-reinforced, water-repellent, hydrated lime and hydraulic binder-based, specific for GASBETON® reinforced masonry skim coating without a base primer, to be applied by hand or with plastering machine. A base for subsequent decorating using plaster finish or silicate or siloxane-based paints. Skim coating thick.: 6-8 mm (minimum 5 mm). Grain size: 0 – 0.6 mm. Colour: white.
code RASOFIN – RASOFIN FIBRE-REINFORCED SKIM COAT FOR EXTERIORS – 25 Kg bag
Anchoring mortars

Idro anchoring mortar
Water-repellent anchoring mortar for laying the first course of GASBETON® blocks.
M10, strongly water-repellent, pre-dosed mortar in two-compartment bags for indoor and outdoor use, siliceous sand-based with specific ARS binders and special additives, suitable for bedding the first course of load-bearing and non-load-bearing masonry, useful for limiting capillary ascending moisture without the use of waterproofing sheaths.
Joint thick.: 20 mm.
code VANCIDRO – IDRO M10 ANCHORING MORTAR – 25 Kg bag

Multimalt
Mortar for anchoring GASBETON® masonry to load-bearing structures.
Premixed mortar for indoor and outdoor use, grey colour, with calibrated water retention, hydraulic binder-based with siliceous sands, synthetic resins and special additives, designed for anchoring GASBETON® infill panels to the vertical load-bearing structures of buildings where there are no movement joints between masonry and pillars.
Joint thick.: 10-20 mm.
code VANCOR – MULTIMALT – 25 Kg bag
Glue and skim coat for mineral insulation

Biokoll Light
GASBETON® ecological glue and skim coat for mineral insulation panels and GASBETON® skim coat for internal walls.
Premixed powder NHL natural hydraulic lime-based, selected light aggregates, reinforcement fibres and additives to improve workability and adhesion to the substrate. Suitable for carrying out reinforced internal skim coating on Gasbeton masonry with a particularly ecological, breathable and healthy product.
Skim coating thick.: 5mm. Grain size < 1.25 mm. Colour: beige.
code BIOKLIGHT – BIOKOLL LIGHT ecological lime-based skim coat for interiors – 20 kg bag

Mykoll
Glue and skim coat for the application of B/THERMO mineral insulating panels at thermal bridges.
Premixed powder composed of cement, limestone aggregates, additives, resins and cellulose, suitable for bonding B/THERMO insulating panels made of calcium hydrate on reinforced concrete load-bearing structures and for carrying out rustic reinforced skim coating prior to the external plastering cycle.
Bonding-skim coating thick.: 3mm-4mm. Grain size < 0.8 mm. Colour: white.
code COL-ISO – MYKOLL skim coat glue in bags for B/THERMO – insulation 25 Kg bag
Primer

Primer GASBETON®
Acrylic primer for indoor and outdoor use to be diluted according to the different uses
GASBETON® PRIMER can be used
- as an additive, in the event of gluing cladding externally onto direct skim coating , to be mixed with M10 RS MORTARGLUE to enhance its characteristics of adhesion to the support, resistance, water-repellency and elasticity;
- as a primer/ consolidating treatment;
- for application onto reinforced concrete pillars/ baffles when aligned with the external/ internal edge of GASBETON® block masonry, to ensure uniform adhesion of MULTICEM and GLUESKIM;
- to be applied onto supports with different degrees of absorption compared to GASBETON® aerated autoclaved concrete blocks, for uniform MULTICEM adhesion.
for application on aerated autoclaved concrete blocks when gluing internal cladding directly onto masonry, without preventive skim coating; - for application onto aerated autoclaved concrete blocks when gluing external cladding onto direct reinforced skim coating;
for the consolidation of uneven or crumbling surfaces
code PRIMER1 – Primer 10 litre cans
Adhesives
GASBETON® adhesive
For the laying of aerated autoclaved concrete blocks
Based on a special low-expanding single-component polyurethane foam formulated for thin-jointed masonry. Ideal for laying GASBETON® blocks, its low-pressure formulation ensures stability and prevents the deformation of masonry during and after work.

Available in 2 versions
Version with spout (already supplied)
Version with gun (can be purchased separately)


Available in 2 versions
Version with spout (already supplied)
Version with gun (can be purchased separately)

Fast
15 minutes Initial hardening

Strong
500 Kg/dm2 adhesion to concrete

Effective
up to 12 sqm with one canister

Benefits
40–60 metre edge
Features:
- Extremely fast laying
- High site cleanliness
- Reduction of thermal bridges in joints
- Less site equipment
- Constant thickness of joints between blocks
- Quick grip in just 15 minutes
- Does not require any construction site equipment
Fields of application:
- GASBETON® block laying
- Joint sealing between masonry and structures
- Bonding plasterboard and gypsum fibre sheets
- Bonding decorative elements, tiles and thresholds
Adhesion values on different substrates:
- Aerated autoclaved concrete blocks: max* (with 1 mm joint)
- Plasterboard Sheets: max* (with 1.5 mm joint)
- Insulating polystyrene and mineral wool panels: max* (with 3 mm joint)
- Concrete: > 500KPa (with 1 mm joint)
- Wood: > 260KPa (with 1.5 mm joint)
- Steel: > 130KPa (with 1.5 mm joint)
* bonding resistance greater than the tear resistance of the substrate.
RANGE:
code VSCHIUMA – GASBETON® adhesive
(by gun) – Canister
code VSCHIUMABEC – GASBETON® adhesive
(with spout) – Canister
code VPUL – GASBETON® foam cleaner
Canister
code VPIST – Gun for GASBETON® adhesive